Tools

1
2
3
4
5
6
Next

Quick view
Compare

JIMS

JIMS Twin Cam Timken Case Bearing Conversion Tool 959

$1,494.10 $1,245.09

A must for the big cubic inch late model Twin Cam engine builder. It may also be used to replace the bearing for stock 88 or 96" engines. Utilizing the special JIMS precision insert, it is designed to easily and accurately convert the left side...

Add to Cart
0
Quick view
Compare

JIMS

JIMS Cylinder Torque Plates 5829

$672.08 $560.07

Simulate stress conditions when boring and honing. Lasered with correct torquing sequence. Made in USA. For use on Milwuakee-Eight models

Add to Cart
0
Quick view
Compare

JIMS

JIMS Main Drive Gear and Bearing Remover/Installer Tool 900

$429.55 $357.96

JIMS has developed a driver style seal installer (not a pushing or pulling type, which could damage these bearings). Complete kit for servicing the main drive gear or the main bearing on the latest 6-speed transmission. This precision tool removes or...

Add to Cart
0
Quick view
Compare

JIMS

JIMS Remote Fuel Supply For Fuel Injected Models Blue 5530

$418.41 $348.68

For H-D models with Delphi fuel injection (except V-Rod). Run EFI motorcycles for testing, service and diagnostics with the stock fuel tank removed. The billet aluminum fuel tank is designed to be pressurized from an air compressor for sending fuel to an...

Add to Cart
0
Quick view
Compare

JIMS

JIMS Bearing and Race Puller 963

$392.42 $327.01

Use to correctly remove press fit; transmission gears and bearings from input and output shafts. Made in USA. Bearing And Race Puller

Add to Cart
0
Quick view
Compare

JIMS

JIMS Inner Cam Bearing Remover Tool 993

$354.44 $295.37

Removes the inner cam bearing. Keeps all pin bearings from falling into the engine case. Install cam bearings with P/N 495146. Made in USA. 06-13 Dyna; 07-12 Big Twin

Add to Cart
0
Quick view
Compare

JIMS

JIMS Vacuum Fed Fork Filling Tool 740

$332.19 $276.83

This patent pending tool will eliminate the need to remove the fairing on all touring bikes to change the fork oil. Changing the fork fluid on models with fairings can be intimidating and take hours. With this tool it should take about 30 minutes to...

Add to Cart
0
Quick view
Compare

JIMS

JIMS Wrist Pin Bushing Reamer Tool 1726-3

$330.68 $275.57

Can be used with rods in or out of motor. Reams wrist pin bushing to H-D specifications. Made to exact tolerances and piloted to locate on the ID of newly replaced wrist pin bushing. Made in USA. 99-06 Twin Cam (exc. 2006 Dyna)

Add to Cart
0
Quick view
Compare

JIMS

JIMS Mainshaft Bearing Race Tool 34902-84

$309.01 $257.51

Used to remove and install the bearing inner race on the transmission mainshaft. Made in USA. L84-14 Big Twin

Add to Cart
0
Quick view
Compare

JIMS

JIMS Sprocket Shaft Bearing Installation Tool 97225-55

$253.96 $211.63

Installs sprocket shaft bearing and pulls lower end into left case. Made in USA. 55-02 Big Twin H-D#97225-55

Add to Cart
0
Quick view
Compare

JIMS

JIMS Rocker Arm Stud Kit 5833

$236.25 $196.87

All Milwaukee-Eight engines incorporate balancers to reduce vibration. JIMS has now developed a balancer bearing installer, which can be used in conjunction with the existing JIMS balancer bearing remover, to precisely install these bearings in the...

Add to Cart
0
Quick view
Compare

JIMS

JIMS Pinion Gear Locking Tool 2237

$199.15 $165.96

Use to lock pinion gear, necessary to torque the pinion nut. Simple to use, align underneath gear and screw into case. Use P/N 496082 tool to tighten pinion nut. Can also be used on aftermarket and S&S motors. Made in USA. Pinion Gear Lock Tool

Add to Cart
0
Quick view
Compare

JIMS

JIMS Fork Stem Bearing Remover 1414

$198.05 $165.04

Use this tool to remove the lower fork stem (Triple Clamp) tapered bearing. Made in USA.

Add to Cart
0
Quick view
Compare

JIMS

JIMS 5-Speed Main Bearing Remover 1720

$197.82 $164.85

Removes the old bearing straight without possible damage to the transmission case and without removing the transmission case. Forget that block of wood and hammer to remove the main bearing. Made in USA. 5-Speed Main Bearing Remover

Add to Cart
0
Quick view
Compare

JIMS

JIMS Fork Seal and Cap Installers 49mm 2049

$196.35 $163.63

Use to install fork seals, dust seals and chrome caps. Lightly grease to keep from scratching fork tubes. Made in USA. 49mm Slider

Add to Cart
0
Quick view
Compare

JIMS

JIMS Connecting Rod Bushing Tool 95970-32C

$180.43 $150.36

Use to remove and replace wrist pin bushings, without removing connecting rod from crankcase. Made in USA. All single Cam Big Twin H-D#95970-32A

Add to Cart
0
Quick view
Compare

S&S

S&S 2-Piece Socket Kit 53-0045

$176.60 $147.16

Allows in-frame installation of S&S compression releases and protects wiring from damage during installation. 2-Piece Socket Kit

Add to Cart
0
Quick view
Compare

JIMS

JIMS Fork Leg and Tube Holder Tool 2251

$168.23 $140.19

Holds fork legs and tubes for easy hands free servicing or rebuilding. Mounts in a vise to hold the fork firmly during repair without causing damage to the fork assembly. Will not scratch finishes. Use on smaller or larger fork tubes with a maximum 2"...

Add to Cart
0
Quick view
Compare

JIMS

JIMS Flywheel Runout (Trueness) Inspection Gauge 785

$165.41 $137.84

Check flywheel runout of the pinion shaft while assembled in engine case; check the amount of gear lash on gear driven cams used in some Twin Cam engines. By using JIMS Tire Rotator P/N 461085 you can remove most all of the stress being applied to the...

Add to Cart
0
Quick view
Compare

JIMS

JIMS Main Drive Gear, Bearing and Seal Installer Tool 986

$159.63 $133.03

Installs main drive gear bearings and seal with use of a small 1-ton press. Holds bearings and seals square to its bore, eliminating any marring of the bearings and seals and installing both to the right depth. Made in USA. Main Drive Gear, Bearing &...

Add to Cart
0

1
2
3
4
5
6
Next

Free Shipping

Discounted Prices

Total:

$0.00

view cart